The Cupboard Under the Sink
By IdentifyThese Editorial · Reviewed · 3 min read
Sink cabinets combine several water connections, an enclosed unventilated space, and a base made of the most absorbent board in the kitchen.
The five leaks
The drain connection at the basket or plughole, where the seal hardens over time.
The trap, particularly at the slip joints, which loosen.
The supply line connections, which weep slowly rather than spraying.
The rim seal around the sink, where water runs down the outside of the bowl. Common with sinks whose sealant has failed, and easy to miss because the leak appears far from the tap.
Condensation on the cold supply pipe in a humid kitchen, which produces steady drips with no fault at all.
| Where the water shows | Likely source |
|---|---|
| Under the trap | Trap joints |
| At the back of the cabinet | Supply connections |
| Spread across the base | Rim seal or a long-standing drip |
| On the pipe itself, in beads | Condensation |
| Only after using the sink | Drain side |
| Constant regardless of use | Supply side |
That last distinction is the fast one. Dry everything, then leave the sink unused for several hours: any new water means a supply or condensation issue, and nothing means a drain fault.
Finding it
Dry the cabinet completely and line it with paper towel or newspaper.
Run the tap hard for a minute, then fill and drain the bowl, then check the paper. Watch the joints with a torch while the water is running.
For a rim seal, run water around the edge of the bowl rather than into it.
The base board
Most cabinet bases are particle board or MDF with a thin laminate. Both swell irreversibly when wet and support growth right through.
Surface staining on an otherwise firm board can be cleaned. A swollen, soft or crumbling board is replaced, and cutting a new base to fit is generally an easy job.
Painting or sealing a damaged board without replacing it traps the problem, in the same way described in mold behind paint and wallpaper.
What is behind and beneath
Water under a cabinet runs along the floor and under adjacent units, so the visible damage is often the smallest part.
Check the flooring at the toe kick, and the wall behind the cabinet. A leak that has been running for months frequently affects the subfloor, which is the expensive part and the reason a small drip is worth chasing early.
Cleaning
Empty the cupboard completely. This is also the moment to discover how many half-used bottles are in it.
Clean hard surfaces with detergent, dry thoroughly with air movement, and use a fan for a day or two before putting anything back.
Fix the leak first. Cleaning a cabinet with an active drip produces the same result again within a month, which is the constant theme of mold removal.
Preventing a repeat
A drip tray or a plastic cabinet liner, which contains a future leak and makes it visible.
Insulating the cold supply pipe where condensation is the cause.
Checking the cupboard twice a year — a torch and thirty seconds — which catches slow leaks while they are still a plumbing job rather than a joinery one.
The dishwasher next door
Frequently the actual source when the cabinet beside the sink is affected. Dishwasher supply and drain connections, and the door seal, all leak slowly, and the appliance hides it completely.
Pulling a dishwasher out is more work than opening a cupboard and it is worth doing when the adjacent cabinet is damp with no fault of its own. Water runs sideways under the units, so the wet cupboard is often not the one containing the leak.
Types referenced
The species matters less than you think
- Public health guidance is to remove all indoor mold regardless of type. The CDC and EPA do not recommend routine species testing for ordinary households, because the response does not change: find the water, stop it, remove the growth.
- “Toxic black mold” is a marketing phrase, not a category. Stachybotrys is real and does need soaked material to grow, so finding it tells you something useful about your building. But the health effects that are well established — allergy, asthma aggravation, irritation — are not specific to it.
- Mold without water does not persist. Cleaning growth while leaving the moisture source is why it comes back. The leak, the condensation or the ventilation is the actual problem.
Call a professional for areas larger than about 10 square feet, for anything in HVAC ductwork, after sewage or flood water, or if anyone in the household is immunocompromised or has a lung condition.
Keep reading
- Bubbling Paint and Peeling WallpaperPaint lifting off a wall is a moisture signal, and what is growing underneath is usually further along than what shows on the surface.
- Removing Mold: What Works, and Why Bleach Usually Isn't ItCleaning the growth without fixing the moisture is why mold comes back. What to use on which surface, what to throw away, and where the DIY limit sits.
- Mold on Cheese: When to Cut It Off and When to Bin ItHard cheese can be salvaged by cutting well clear of the mold. Soft cheese cannot, because the mold has already grown through it.